APRS functions Manual
Geosat 6 APRS can auto-delete the received APRS contacts positions based on a user dened timeout. You can also sort your APRS contacts based o
On the full info page of the APRS contact, you can set the APRS contact as Target, by touching the Set as Target button.This allows you tracking a mov
right corner of the screen. Tracking the position of the target: Once you have set the APRS contact as target, the Target button with a target
The Messages page is enabled when a Geosat 6 APRS is connected to a compatible radio transceiver or modem supporting the Messaging function.
ABC. To change the characters from small to CAPITAL, • use the buttons on the right: “A” for the Capital keyboard or “a” to go back to the small key
In the APRS options menu you can edit settings for the contacts management: Contacts sorting (Chap V), Contacts Timeout (Chap V), for Messages display
The Geosat 6 APRS comes with an APRS bi-directional RS-232 APRS interface compatible with all APRS Kenwood amateur radios models and with all the TNC
Type of radio transceiverGeosat 6 APRS functions/ Kenwood sentence compatible NMEA sentence onlyAPRS icons All standard iconsOnly xed / movingAPRS co
Hardware• Dimensions and weight: 133.6 x 83.4 x 21 mm; 270 g• Memory Support: Secure Digital• Display: touch screen LCD 4.8”, 65536 colors• Resolution
• Intercept to target function• Tactical mode• Store up to 1000 APRS contacts• APRS contacts auto-delete• APRS contacts sorting• Standard APRS iconsAP
Your journey, Our technology
Appendix: Units setup Set up instructions for:Geosat 6 APRS APRSwith the following devices:• Kenwood TH-D72 A/E• Kenwood TM-D710 A/E• Kenwood TM-D700
Set-up for the Kenwood TH-D72A/E with the AvMap Geosat 6 APRSThese instructions provide the essential information necessary to congure your AvMa
settings below. Leave all other settings at default, for now. Note: only important default settings are included here.• Press the Menu button again t
Menu Number Description Setting332 Output On340 Format KENWOOD341 Length 9-Character342 Output All (during setup)370 Speed On (during setup)371 Altitu
Menu Number Description Setting3H2 Total Hops 2 (during setup)3J0 TX Off3K0 Digipeat (MyCall) Off3T0 RX Beep All (during setup)3T1 TX Beep (Beacon) On
3. Turn on the Geosat G6 APRS and the TH-D72A/E. Wait until the Geosat 6 APRS has acquired sufcient satellites to establish a 3D position. A b
an ohmmeter, especially if it is a home brewed data cable.4. Verify that the Geosat 6 APRS is computing a posi-tion x.5. Listen to your APRS frequenc
Set-up for Kenwood TM-D710 A/Ewith the AvMap Geosat 6 APRS NOTE: These instructions assume you have basic familiarity with operation of both t
Beacon TX Algorithm Menu # 611a. Set the Method to “smart beacon”b. Press ESC to return to the main pagec. Change the APRS Frequency to: 144.390d. Sel
map, or translate the map to a different location in order to see them. You can also verify this in the APRS Contacts folder. The Geosat 6 AP
I. Introduction 4II. Quick Set-up 5III. Activating the APRS mode 6IV. Finding APRS Contacts 7V. Managing APRS contacts 10VI. Setting an A
Set-up for Kenwood TM-D700 A/Ewith the AvMap Geosat 6 APRSNOTE: These instructions assume you have basic familiarity with operation of both th
Making it all work!a. Make sure both the Kenwood TM-D700 and AvMap Geosat 6 APRS are turned OFF!b. Connect the four pole 2.5mm communication cab
Check for a good click into the unit.c. NOW POWER UP BOTH UNITS!d. If your Kenwood D700 powers up in VFO mode (voice communications) push and
Set-up for Kenwood TH-D7 A/Ewith the AvMap Geosat 6 APRS NOTE: These instructions assume you have basic familiarity with operation of both the
Making it all work!a. Make sure both the Kenwood TH-D7 and AvMapGeosat 6 APRS are turned OFF!b. Connect the four pole 2.5mm communication cable end to
www.geosat6.com
APRS is a method for sending and receiving position and other information over a radio transceiver.The Geosat 6 APRS is ready to accept APRS inputs fr
How to set-up your transceiver: Enter your call sign • BAUD Rate=9600 • Waypoint=ALL • Waypoint size=9 character (this as also called • waypoint lengt
To enter in the APRS mode, open the main navigation menu and press the APRS Functions button. To enable or to disable the APRS mode, press th
APRS icons on the map:As soon as you connect Geosat 6 APRS to your transceiver you will start receiving APRS positions called “APRS contacts”.
sort them or delete them by entering the APRS contacts Menu. To enter in the APRS Contacts Menu, press the APRS Contacts button in the APRS Function
Delete• : Touch this button to delete the selected APRS contact from the APRS contact list.Save as contact• : touch this button to sav
Commentaires sur ces manuels